External elements of the car body Mercedes G-Class (W463)

Specifications of the body and its elements
Body Serial designation 463 Design The body is located on a curved ladder frame with increased torsional rigidity, bolted to the frame on rubber mounts Bottom and wheel...

Removing and installing wiper arms
Windshield Removing the windshield wiper arm 1 - Cover 2 - Nut 3 - Lever 1. Remove the key from the ignition switch to prevent the windshield wipers from spontaneous...

Removing the front wiper drive
Details of installation of a drive of forward screen wipers 1 - Nuts; 2 - Anther; 3 - Washer; 4 - Sealing washer; 5 - Crank; 6 - Thrust; 7 - Spindles 1. Remove the key...

Removal and installation of a cowl
Converting the hood to a vertical position 1 - Latch release lever; 2 - Safety hook; 3 - Holder; 4 - Gas-filled stop 1. Pulling the lever (1) on the left under the...

Removal and installation of the lock of a cowl
Attention! All self-locking fasteners must be replaced without fail! Except models 463.333 Bonnet lock installation details (except models 463.333) 1, 3 - Bolts; 2 -...

Removal and installation of a drive cable of release of a latch of the lock of a cowl
Details of installation of a cable of a drive of a release of a latch of the lock of a cowl (1 of 2) 1 - Latch release lever; 2 - Bolt; 3 - Drive cable Details of...

Removal and installation of a forward lattice
Front grill installation details 1 - Fixing nuts; 2 - Front grille; 3 - Mounting clips; 4 - Hose; 5 - Distributing fitting; 6 - Nozzle; 7 - Clamp 1. Open the hood. 2....

Removal and installation of covers of block headlights
Headlight cover installation details 1 - Bolt; 2 - Cover; 3 - Guides; 4 - Headlight washer hose 1. Remove the front grill (see Section Removal and installation of a...

Removal and installation of an anther of an impellent compartment of a complete set AMG
Installation details of the lower anther of the engine compartment on AMG equipment models 1 - duster; 2, 3 - Screws; 4 - Mounting bracket 1. Jack up the car and put it...

Removal and installation of side steps
Details of fastening of the front part of the side step 1 - Top screw; 2 - Locker; 3 - Front screw Side step attachment details (on the example of a model with a...

Removal and installation of bumpers
Front bumper Front bumper installation details 1 - Bolts; 2 - Bumper; 4 - ATF cooler; B14x1 - Outside air temperature sensor connector 1. On models of the corresponding...

Removal and installation of door rear-view mirrors
Door mirror installation details 2 - Bolts 6 - Mirror Door mirror wiring harness 1 - Retainer 3 - wiring harness X141 - Left mirror wiring connector X141 / 1 - Right...

Removal and installation of the glass washer fluid reservoir
Washer fluid reservoir installation details (except models 463.323) (1 of 2) 1 - Expansion tank of the cooling system; 3 - Nut; 4 - Filler neck; 9 - Mounting bolts...

Removal and installation of the spare wheel holder
Installation details of the outer spare wheel holder 1 - Spare wheel casing; 2 - Support bracket; 3 - Bolts; 4 - Remote bushings; 5 - Rubber sealing elements; A - Models...

Removal and installation of wheel arch protection lockers
Details of the installation of the wheel arch protection locker, - the arrows show the places where the self-tapping screws are screwed 1. Turn out the screws (arrows)...

Removing and installing A-pillar exterior trim panels
A-pillar Exterior Trim Panel Installation Details 6 - Finishing panels Arrows - Rivets 1. Drill out the rivets (arrows) and remove trim panels (6). 2. Installation is...

Removal and installation of front fenders
Attention! All self-locking fasteners must be replaced without fail! Front fender installation details (1 of 3) 1 - Locker; 2 - Air intake grille; 3, 8, 11 - Bolts; 4 -...